Epoxy Calculator
Knox Epoxy Pros is a referral service for epoxy and concrete floor coatings in Knoxville and East Tennessee. Enter your garage dimensions to get square footage, how much coating the floor needs, and an installed price range by system.
Typical Knoxville garages
| Garage | Square feet | Flake coating | Flake epoxy installed |
|---|---|---|---|
| 1-car garage | 240–300 | 3.5–4.5 gal | $1,200–$3,000 |
| 2-car garage | 400–500 | 5.5–7.5 gal | $2,000–$5,000 |
| 3-car garage | 600–750 | 8–11.5 gal | $3,000–$7,500 |
The gallons column is a flake build: a pigmented epoxy basecoat and a clear polyaspartic topcoat, each 10 to 12 mils dry. Film thickness sets coverage. One gallon of 100%-solids resin rolled out one mil thick would cover about 1,604 square feet, so a 10-mil coat covers about 160 and a 12-mil coat about 134. A big-box kit claims more coverage per gallon because it goes on thinner, which is the same reason those floors commonly fail inside two to three winters in Tennessee humidity.
Coverage by system, coat by coat
- Solid-color epoxy: 50–62 sq ft per gallon of total material
- Basecoat (pigmented epoxy, 10–12 mils), Topcoat (pigmented epoxy, 16–20 mils). Rates from the Floorguard Products, Medium Duty Solid Industrial System sheet.
- Flake (chip) epoxy: 68–77 sq ft per gallon of total material
- Basecoat (pigmented epoxy, 10–12 mils), Topcoat (clear polyaspartic, 10.7–12 mils). Rates from the Floorguard Products, FGP Flake System sheet.
- Polyaspartic system: 75–80 sq ft per gallon of total material
- Basecoat (pigmented polyaspartic, 10–10.7 mils), Topcoat (clear polyaspartic, 10–10.7 mils). Rates from the Floorguard Products, FGP Polyaspartic Flake System sheet.
- Metallic epoxy: 28–34 sq ft per gallon of total material
- Basecoat (pigmented epoxy, 10–12 mils), Metallic build coat (epoxy with metallic pigment, 32–40 mils), Topcoat (clear urethane, 5 mils). Rates from the Floorguard Products, Metallic Marble System sheet.
Checked November 2026. Left out: the moisture primer (about 90 square feet per gallon) that only a slab failing a moisture test needs, and the broadcast flake itself, which runs about 0.13 pounds per square foot at full coverage. Another brand’s figures shift with its own film thickness.
Common questions
- How much epoxy do I need for a 2-car garage?
- It depends on the system more than the garage. On a typical Knoxville 2-car slab of 400 to 500 square feet, a flake floor uses 5.5–7.5 gallons across its basecoat and clear topcoat, a solid-color floor 6.5–10 gallons (its second coat is laid thicker), and a metallic floor 12–18 gallons, because the metallic layer alone goes down 32 to 40 mils deep. Those rates are a manufacturer's published coverage per coat. Thin DIY kits list far more square feet per gallon because each coat is only a few mils, which is also why they wear through sooner.
- How do I measure my garage floor?
- Measure the width and the depth in feet at the widest points, then multiply. Do not subtract for the car; the whole slab gets coated. If the garage is an irregular shape, split it into rectangles, work out each one, and add them together.
- Is this an epoxy flooring cost calculator too, or just a coverage calculator?
- Both. It leads with coverage — square footage and gallons — because that is the number a floor actually needs first, but the third output is an installed cost range for your dimensions in whichever system you pick. The ranges come from the same published Knoxville prices as the cost guide, so the two pages cannot disagree.
- Is the price this calculator gives me a quote?
- No. It is a planning range built from real Knoxville installed prices by system. The final number depends on the condition of your concrete — crack repair, joint work, or grinding off an old failed coating all add labor before any new coating goes down. An exact price needs an on-site look at the slab.
Ready for a floor that actually lasts?
Describe the floor and we pass it to an independent local installer in Knoxville. Asking is free.